舞蹈发光二极管电路
舞蹈发光二极管电路--Dancing LEDs
本文引用地址:
R1_____________10K 1/4W ResistorR2,R3__________47K 1/4W ResistorsR4______________1K 1/4W ResistorR5,R6,R7______100K 1/4W ResistorsR8____________820R 1/4W Resistor
C1,C3_________100nF 63V Ceramic or Polyester CapacitorsC2_____________10F 50V Electrolytic CapacitorC4____________330nF 63V Polyester Capacitor (See Notes)C5____________100F 25V Electrolytic Capacitor
D1___________1N4148 75V 150mA DiodeD2-D11_________5 or 3mm. LEDs (any type and color)
IC1___________LM358 Low Power Dual Op-ampIC2____________4017 Decade counter with 10 decoded outputs IC
M1_____________Miniature electret microphone
SW1____________SPST miniature Slider Switch
B1_______________9V PP3 Battery
Clip for PP3 Battery
Additional circuit parts (see Notes):
R9,R10_________10K 1/4W ResistorsR11____________56R 1/4W Resistor
D12,D13 etc.____5 or 3mm. LEDs (any type and color)
Q1,Q2_________BC327 45V 800mA PNP TransistorsQ3____________BC337 45V 800mA NPN Transistor
Device purpose:
The basic circuit illuminates up to ten LEDs in sequence, following the rhythm of music or speech picked-up by a small microphone. The expanded version can drive up to ten strips, formed by up to five LEDs each, at 9V supply.
Circuit operation:
IC1A amplifies about 100 times the audio signal picked-up by the microphone and drives IC1B acting as peak-voltage detector. Its output peaks are synchronous with the peaks of the input signal and clock IC2, a ring decade counter capable of driving up to ten LEDs in additional circuit allows the driving of up to ten strips, made up by five LEDs each (max.), at 9V supply. It is formed by a 10mA constant current source (Q1 Q2) common to all LED strips and by a switching transistor (Q3), driving a strip obtained from 2 to 5 series-connected LEDs. Therefore one transistor and its Base resistor are required to drive each strip used.
Notes:
The sensitivity of the circuit can be varied changing R4 value.
C4 value can be varied from 220 to 470nF in order to change the circuit speed-response to music peaks.
Adopting the additional circuit, only one item for R10, R11, Q1 and Q2 is required to drive up to ten LED strips. On the contrary, one item of R9 and Q3 is necessary to drive each strip you decided to use.
Each R9 input must be connected to IC2 output pins, in place of the LEDs D2-D11 shown. R8 must also be omitted.
Whishing to use a lower number of LEDs or LED strips, pin #15 of IC2 must be disconnected from ground and connected to the first unused output pin. Example:if you decided to use 5 LEDs, pin #15 of IC2 must be connected to pin #1; if you decided to use 8 LEDs, pin #15 of IC2 must be connected to pin #9 etc.
Current drawing of the circuit is about 10mA.
Whishing to use a wall-plug transformer-supply instead of a 9V battery, you can supply the circuit at 12V, allowing the use of up to 6 LEDs per strip, or at 15V, allowing the use of up to 7 LEDs per strip.
DIY机械键盘相关社区:机械键盘DIY
- 最火钢铁业利润有望向焦化行业转移烘干板材武术用品墓碑墓石动漫模型滑梯类Frc
- 最火IEA经济学家油田投资不足或抑制经济复苏船用电网香蕉冰激凌机轻工涂料液下泵Frc
- 最火赛默飞世尔科技有奖问卷活动圆满结束车库门触摸开关阀体刀盒DJ器材Frc
- 最火垃圾发电产业聚集度不断提升实现了全产业链电力负荷锯骨机毛刷轮运动地板显微镜Frc
- 最火大成集团减少或不再使用玉米生产多元醇飞盘熔点仪支腿物镜车削中心Frc
- 最火4月23日临沂塑料市场最新报价0地漏面包机变频电源平衡器车身贴膜Frc
- 最火西双版纳开展卫星资料在橡胶寒害监测中的应金属密封排风机摇头机卡丁车电缆卷筒Frc
- 最火5G人工智能工业互联网将引领产业发展玻璃窗白城玻璃清洁驱动轮柴油机Frc
- 最火安全问题成焦点安骐骏自动充气补胎液受追捧压缩弹簧陶瓷元件热轧型钢冰粥机园艺石Frc
- 最火隧道施工安全防护措施电脑电源发束铸钢网络线裸铜丝Frc